Slowly and carefully add 7.6 ounces of lye to 16.4 ounces of distilled water. Gently stir until the lye has fully dissolved. Set it aside to cool. If you’d like a harder bar of soap that releases faster from the mold, you can add sodium lactate to the cooled lye water. Use 1 teaspoon of sodium lactate per pound of oils in the recipe. For this recipe, you’d add 3.5 teaspoons sodium lactate.

Melt and combine 13.8 ounces of coconut oil, 2.8 ounces of jojoba oil, 5.5 ounces of squalane oil, 2.8 ounces of argan oil, 16.5 ounces of olive oil, and 13.7 ounces of palm oil (completely melt the entire container of palm oil before portioning) into a large mixing bowl. Once the lye water and the oils have cooled to 130 degrees F or below (and are ideally within 10 degrees of each other), add the lye water to the oils and stick blend the mixture to a very thin trace.

Pour off 800 mL of soap into a separate container and add 1.5 teaspoons of dispersed activated charcoal.

Add a proportional amount of the measured Birchwood Oud Fragrance Oil to the gray soap – it’s okay to eyeball it.

Stick blend the soap for a few pulses to fully mix in the fragrance and colorant, and to reach a slightly thicker trace. The soap needs to be thin enough to pour and spread out in the mold evenly. You want the soap to be smooth and not hold any texture. That will give you the straightest layer.

Pour all of the gray soap into the mold. Tap the mold on the counter to help get rid of bubbles and to evenly distribute the soap.
NOTE: If this layer of soap gets too thick, you may want to texture the soap with a spoon to create a purposefully uneven layer. It will still look great, just a little bit different.

Place a spoonful of activated charcoal into a Powder Duster. Use your finger to gently tap the Powder Duster and apply a thin, even layer of charcoal. Work quickly but carefully – activated charcoal can be a pain to clean up. Once the entire layer of soap is covered with a layer of charcoal, set the mold aside.

Section off the remaining soap into separate containers. Add the following amounts of dispersed colorants to each container, and mix them in with a whisk.

• Container A (700 mL): All dispersed titanium dioxide
• Container B (400 mL): Remaining dispersed activated charcoal
• Container C (400 mL): 1/4 teaspoon dispersed Green Chrome Oxide + 1/2 teaspoon dispersed Evergreen Mica

Pour the remaining Birchwood Oud Fragrance Oil into the three containers proportionally – it’s okay to eyeball it. Use a whisk to fully mix in the fragrance.

Begin pouring white soap into the large bowl, allowing it to run down the side.  As you pour, count 1, 2, 3, 4 to keep each pour consistent. The exact amount of soap you pour at a time is up to you. The more soap you pour into the bowl at a time, the fewer total layers there will be.
NOTE: We tilted the bowl while pouring to help the soap run down the side of the bowl more. This could make pouring trickier. If it feels too unstable, leave the bowl level on the table. Just be very careful when pouring that the soap doesn’t drop into the soap and break through to the layers in the bowl. 

Continue pouring the soap into the bowl in the pattern of white, black, white, green. Counting while pouring helps keep the pours consistent.

Once all of the soap is in the large bowl, begin to pour the soap into a corner of the mold. Be very careful – you don’t want the soap to break through the layer below.

As the mold begins to fill up, slowly move the bowl down the length of the mold while pouring.

Once there is about 1/4 of the soap left to pour, begin moving the bowl down the length of the mold more and more to create long stripes. Try to pour as straight as you can.

Once all the soap has been poured, tap the mold on the counter to get rid of bubbles. Spritz the top with 99% isopropyl alcohol to prevent soda ash. To help the colors pop, we forced the soap through gel phase by placing it on a heating pad set to medium-high for about 1-2 hours. We covered the mold using cardboard and a towel to insulate for 24 hours.

Remove the soap from the mold after 1-3 days (depending if you used sodium lactate or not). Cut the soap into bars. After the bars were cut, we used the Soap Shaver to smooth the tops. Adjust the shaver to only slice off a small amount and quickly slide the soap over the blade. Continue to do this until you’re happy with the look of the top. Allow the soap to cure for 4-6 weeks and enjoy!

The two bars in the top left haven’t been shaved while the three bars on the right have. You’ll notice the Soap Shaver took off a bit of soda ash, which made the colors look more vibrant. The smooth and even texture also looks more polished.