Slowly and carefully add 8.4 ounces of lye to 18.8 ounces of distilled water. Gently stir until the lye has fully dissolved. Set it aside to cool. If you’d like a harder bar of soap that releases faster from the mold, you can add sodium lactate to the cooled lye water. Use 1 teaspoon of sodium lactate per pound of oils in the recipe. For this recipe, you’d add 4 teaspoons sodium lactate.

Melt and combine 1.2 ounces of castor oil, 16.2 ounces of coconut oil, 4 ounces of apricot kernel oil, 6.2 ounces of sweet almond oil, 16.2 ounces of olive oil, and 16.2 ounces of palm oil (remember to fully melt then mix your entire container of palm oil before portioning) into a large mixing bowl. Once the lye water and the oils have cooled to 130° F or below (and are ideally within 10 degrees of each other), add the lye water to the oils and stick blend the mixture to a thin trace.

Split the soap batter into four separate containers. Two containers should contain 600 mL, and the other two containers should contain 700 mL.

Add the following amounts of dispersed colorants to each container and use a whisk to incorporate.

• Container A – lightest green (700 mL): 2 tablespoons dispersed titanium dioxide + 1/2 teaspoon dispersed Hydrated Chrome Green Pigment
• Container B – light green (600 mL): 1 teaspoon dispersed titanium dioxide + 1/2 teaspoon Hydrated Chrome Green Pigment
• Container C – medium green (700 mL): 1 teaspoon dispersed Hydrated Chrome Green Pigment
• Container D – darkest green (600 mL): 1.5 teaspoons dispersed Hydrated Chrome Green Pigment + about 1/8 teaspoon dispersed Black Oxide Pigment

Add the 4 ounces of Midnight Waters Fragrance Oil evenly to each container (it’s okay to eyeball it).

Pour about 100-150 mL of the lightest green soap (container A) and 100-150 mL of the medium green soap (container C) into the squeeze bottles. Screw on the lids and set aside.

If the soap is still at a thin trace, stick blend each container from lightest to darkest until all four colors are a medium trace. Pour all of the darkest green soap into the mold. Use a spoon to create peaks and divots into the soap.

Pour all of the medium green soap into the mold. Tap firmly on the counter to get rid of bubbles, then use a spoon to create peaks and divots into the medium green soap layer.

Pour all of the light green soap into the mold. Tap firmly on the counter to get rid of bubbles, then use a spoon to create peaks and divots into the light green soap layer.

Pour all of the lightest green soap into the mold. It will fill to the very top of the silicone liner. Use a large spoon or spatula to evenly spread the soap to create a smooth and even base to create the scales.

Creating the scales involves squeezing dots of soap and then using a spoon to lightly press and slide down. The soap should be thin enough that it can be squeezed out of the bottles, but thick enough that it holds its shape. To get the feel for it, you may want to practice a few scales on a paper towel. If the soap doesn’t come out easily, cut a small portion of the squeeze bottle tip off to create a larger hole. You’ll also need a spoon with a slightly pointed tip. If the spoon tip is too round, it may be difficult to create the scales. Make sure your spoon is not aluminum, which reacts with the lye and creates toxic fumes. You will also need paper towels on hand to clean off the spoon in between different colors of scales.

Working quickly, create five dots of color across the top of the mold, swapping the color with each dot. The dots should just touch. Once you have placed five dots, Use the spoon to gently press each dot of color, sliding the spoon toward you. Between each color, clean off the spoon on the paper towel or rag.
NOTE: In the photos below, you can see that in the first row we placed 6 dots. We found this to be a little bit tight, and switched to only 5 dots in the next layer. 

In the second row, switch the color order so that you squeeze a light green dot onto a dark green dot in the layer above, and vice versa. Use the spoon to gently press each dot of color, sliding the spoon toward you. Continue swapping the color order for each row.
TIP: To keep the process going as quickly as possible, squeeze one color of dots first, and fill in the row with the other color. This eliminates picking up the bottles as often, and helps speed the process along. 

As you work, the soap will continue to thicken. This is why it’s important to work carefully but also quickly. Don’t worry about each scale being completely perfect.

Once we got to about the middle of the mold, our soap was getting quite thick. It was still workable, but required us to tap the squeeze bottle on the counter to transfer the soap to the top of the bottle. We also cut off the very tip to produce a larger hole for the soap to be squeezed through.

Continue squeezing scales until you reach the very end of the mold.

Once the top is completely decorated, use the powder sprayed filled with Super Pearly White Mica to dust a light layer on top. It’s tricky to see in photos, but the mica really makes the scales pop.

Spray the soap with 99% isopropyl alcohol to prevent soda ash. To promote gel phase, place the soap on a heating pad set to medium for 30-60 minutes. To help insulate, we bent a piece of cardboard and placed it over the mold without touching the top. Allow it to stay covered for at least 6 hours. Keep an eye on it to make sure it doesn’t get too hot and crack. If you see a crack starting to form, take it off the heating pad and remove any insulation.

After about 1-3 days (depending if sodium lactate was used or not), remove the soap from the mold and silicone liner. Cut into thick bars to allow 2 rows of scales to be seen in each bar. After cutting, allow them to cure for 4-6 weeks and enjoy.

We used the Soap Beveller to finish these bars. Below, you can see the difference between beveled and non-beveled soap.